JGMaker is having a CLEARANCE sale on the commercial-grade Z-603S -- at a BONKERS $399. If you're in the USA, and want a ready-to-go full steel frame printer... run, don't walk! ⏩ JGAURORA Z603S CLEARANCE ⏪ Only 4 units left!

JGAurora A5S on Sale at Amazon USA - $339, with $60 off!
JGMaker Magic on Sale for $208, with $20 instant discount coupon!.

Getting Started & Troubleshooting

Re-installing cura 3.6

rhaub101 57 views 0 comments 0 points Most recent by rhaub101 December 2018
PLA residue left on bed after printing too close

ryanh1904 232 views 4 comments 0 points Most recent by Samuel Pinches December 2018
Heating problem...

elbico 112 views 2 comments 0 points Most recent by Samuel Pinches December 2018
A5 even more problems now with community firmware?

davidgotmilk 96 views 1 comment 0 points Most recent by Samuel Pinches November 2018
Z axis move and stop

Fieldy 53 views 0 comments 0 points Most recent by Fieldy November 2018
Started printing with the A5, problems with new firmware and stepper drivers.

Prokktor 294 views 18 comments 0 points Most recent by Prokktor November 2018
Strange problem with A5 (only when USB connected)

Manu1001 108 views 0 comments 0 points Most recent by Manu1001 November 2018
Many Problems with the A5

jirgel 1K views 50 comments 0 points Most recent by jirgel November 2018
spare parts

Matt 175 views 2 comments 0 points Most recent by Matt November 2018
Warping Problems

Prokktor 569 views 42 comments 0 points Most recent by netzmark November 2018
Strange First Layer Printing Problems

rhaub101 355 views 21 comments 0 points Most recent by Prokktor November 2018
JGAURORA A5 - A very disappointing 3D Printer

JayJoe 2.6K views 37 comments 0 points Most recent by netzmark November 2018
Cura 3.6.0 on my A5.......im impressed

Auswanderer 375 views 4 comments 0 points Most recent by sasa November 2018
Distance between nozzle and heatbed after leveling

dope76 1K views 64 comments 0 points Most recent by cybercow November 2018
What in the is causing this noise

itisnot_me 352 views 12 comments 0 points Most recent by itisnot_me November 2018
Fan doesn't turn on automatically

PeanutPrinter 76 views 3 comments 0 points Most recent by Prokktor November 2018
Back half of model lifted off bed

rhaub101 55 views 3 comments 0 points Most recent by Auswanderer November 2018
A5 setep motor error

okan 71 views 3 comments 0 points Most recent by Samuel Pinches November 2018
Power suply

daillew321 35 views 2 comments 0 points Most recent by Samuel Pinches November 2018
A5 Rocker Power Switch will not move to off position.

t3flondon 229 views 5 comments 0 points Most recent by Clintor24 November 2018
Can't heat hot end (Error Heating Failed...)

Rubymania 92 views 1 comment 0 points Most recent by Samuel Pinches November 2018
My X- Y- axis completely out (TMC2130 V1.1 (NEW SPI Version) Stepper Motor Drivers )

Dwayne Haynes 259 views 4 comments 0 points Most recent by Samuel Pinches November 2018
extruder motor clicking

Robert 331 views 4 comments 0 points Most recent by Robert November 2018
Blackened plastic oozing from nozzle

Prokktor 111 views 2 comments 0 points Most recent by Prokktor November 2018
below a .2mm layer height

itisnot_me 143 views 5 comments 0 points Most recent by Prokktor November 2018
Repeated movement with no extrusion

itisnot_me 65 views 3 comments 0 points Most recent by Samuel Pinches November 2018
Problems getting a good print, poor quality and looks terrible.

DIYglenn 1.2K views 38 comments 0 points Most recent by DIYglenn November 2018
More Noob questions: My BRIM is curling and tolerance problems:

Prokktor 199 views 12 comments 0 points Most recent by Samuel Pinches November 2018
A5 bed heater cycling

Godzilla32 111 views 5 comments 0 points Most recent by Jamal3f November 2018
Supports in cura

Airtent 553 views 8 comments 0 points Most recent by sasa November 2018