Getting Started & Troubleshooting

Discussion List

• 
  Extruder motor question

  rhaub101 77 views 2 comments 0 points Most recent by rhaub101 September 2018
• 
  Loose x-axis coupling and other annoyances

  delirii 75 views 1 comment 0 points Most recent by delirii September 2018
• 
  weird layer issue...

  CoDdis 75 views 1 comment 0 points Most recent by Samuel Pinches September 2018
• 
  Extruder clicking noise at retracts and when changing filament

  DIYglenn 504 views 5 comments 0 points Most recent by allengregoryiv September 2018
• 
  Calibration cube to big

  Gonzo 114 views 1 comment 0 points Most recent by Gonzo September 2018
• 
  Spring supports....opinions?

  rhaub101 205 views 16 comments 0 points Most recent by Samuel Pinches September 2018
• 
  printing in the bottom left corner (a5)

  golfprolaurence 71 views 1 comment 0 points Most recent by Samuel Pinches September 2018
• 
  Change max retraction speed in community firmeare

  compman2 117 views 1 comment 0 points Most recent by Samuel Pinches September 2018
• 
  Heating failed, Heatbed

  Tim92 140 views 10 comments 0 points Most recent by Tim92 September 2018
• 
  Printing is automatically paused - need HELP!

  Oliver Waller 367 views 5 comments 0 points Most recent by hver September 2018
• 
  Keep your eyes open when filament buying

  AETEK 161 views 3 comments 0 points Most recent by lsh60 September 2018
• 
  A5 bed replacement

  sasa 141 views 0 comments 0 points Most recent by sasa September 2018
• 
  Change filament mid print

  Mathieu Grumplefix Evain 765 views 4 comments 0 points Most recent by Samuel Pinches September 2018
• 
  Wobbely wobbely - need advice on....no clue what I'm looking at...

  wolph42 131 views 3 comments 0 points Most recent by wolph42 September 2018
• 
  Please Diagnose my symptoms

  GoreWolf 192 views 10 comments 0 points Most recent by Samuel Pinches September 2018
• 
  Print Resume Feature

  Olivier 174 views 2 comments 0 points Most recent by Samuel Pinches September 2018
• 
  Left z axis lead screw gets stuck

  Josh3D 492 views 2 comments 0 points Most recent by DIYglenn September 2018
• 
  Cura - fine setting - no bed adhesion

  wolph42 513 views 2 comments 0 points Most recent by wolph42 September 2018
• 
  My A5 stopped in the middle of a print, no problems found.

  DIYglenn 72 views 0 comments 0 points Most recent by DIYglenn September 2018
• 
  Throat(Tube) broken inside the heatsink (x-axis holder)

  Printok 481 views 3 comments 0 points Most recent by Printok September 2018
• 
  What is the screw size that holds the extruder fan duct in place?

  compman2 139 views 2 comments 0 points Most recent by Samuel Pinches September 2018
• 
  LCD Panel will not operate printer

  Wingnut 91 views 3 comments 0 points Most recent by Samuel Pinches September 2018
• 
  Parts listing?

  enochroot 80 views 2 comments 0 points Most recent by enochroot August 2018
• 
  Another bed heating Problem

  Charly3 293 views 10 comments 0 points Most recent by Samuel Pinches August 2018
• 
  Manual Bed Leveling Z-height

  Hevilp 115 views 3 comments 0 points Most recent by Samuel Pinches August 2018
• 
  Need Help with Troubleshooting Blobs

  nottub 221 views 7 comments 0 points Most recent by nottub August 2018
• 
  Error when trying to update firmware

  1980ace 108 views 2 comments 0 points Most recent by 1980ace August 2018
• 
  Printing process interruption

  Werewolf 111 views 1 comment 0 points Most recent by Samuel Pinches August 2018
• 
  Pronterface, new problem with Jgaurora A5 "Thermal Runaway"

  coffeeroast 477 views 2 comments 0 points Most recent by coffeeroast August 2018
• 
  Jgaurora a5 heating_id:0 error

  okan 106 views 3 comments 0 points Most recent by Samuel Pinches August 2018