Getting Started & Troubleshooting

Discussion List

• 
  Extruder and Bed same temp problems

  Ophiocos 410 views 47 comments 0 points Most recent by Ophiocos June 2018
• 
  FAQ: Getting Started & Troubleshooting

  Announcement Samuel Pinches 1.9K views 1 comment 0 points Most recent by Samuel Pinches June 2018
• 
  Firmware Upgrade

  victagayun 293 views 3 comments 0 points Most recent by Samuel Pinches June 2018
• 
  Bed Temp after Printing

  victagayun 185 views 7 comments 0 points Most recent by Samuel Pinches June 2018
• 
  Stepper Driver: Y driver error detected

  Hevilp 156 views 2 comments 0 points Most recent by Hevilp June 2018
• 
  Possible to print without filament?

  Hevilp 64 views 2 comments 0 points Most recent by Hevilp June 2018
• 
  print pop off plate during resume on A5

  enochroot 174 views 4 comments 0 points Most recent by enochroot June 2018
• 
  Glass Released from heat element

  Hevilp 102 views 4 comments 0 points Most recent by Hevilp May 2018
• 
  A5 motors are not moving after repairing fried MKS board

  hundemann 391 views 9 comments 0 points Most recent by Samuel Pinches May 2018
• 
  Neverending Story extruder

  Hevilp 196 views 2 comments 0 points Most recent by Hevilp May 2018
• 
  Thermistor

  Hevilp 644 views 12 comments 0 points Most recent by Samuel Pinches May 2018
• 
  Many functions are not responding.

  Luka 96 views 6 comments 0 points Most recent by Luka May 2018
• 
  How-To: Resume stopped print (with Repetier Server)

  Hevilp 258 views 1 comment 0 points Most recent by Samuel Pinches May 2018
• 
  Layer Shift

  g_pwn 129 views 2 comments 0 points Most recent by g_pwn May 2018
• 
  New A5...No Files Found

  ehlersd 574 views 2 comments 0 points Most recent by TapNorX May 2018
• 
  GRID_MAX doesnt affect

  Hevilp 67 views 2 comments 0 points Most recent by Hevilp May 2018
• 
  Isolation of thermistor

  Hevilp 96 views 2 comments 0 points Most recent by Hevilp May 2018
• 
  Hotend is full of filament

  Hevilp 546 views 11 comments 0 points Most recent by Robert May 2018
• 
  Which Slicer do you use?

  Hevilp 561 views 5 comments 0 points Most recent by Robert May 2018
• 
  Damage to black coating on build plate.

  Cybele999 353 views 1 comment 0 points Most recent by Robert May 2018
• 
  Stops printing mid print

  Mookie117 1K views 12 comments 0 points Most recent by Samuel Pinches May 2018
• 
  Just added the A5 to my collection

  Ap3rc0 67 views 0 comments 0 points Most recent by Ap3rc0 May 2018
• 
  A3S HOME does not work

  blong 104 views 11 comments 0 points Most recent by Samuel Pinches April 2018
• 
  Sometimes filament is not going properly out

  Hevilp 500 views 13 comments 0 points Most recent by djaurora April 2018
• 
  Re-burning bootload on A5

  g_pwn 230 views 21 comments 0 points Most recent by Samuel Pinches April 2018
• 
  Higher support (~>3cm fails) and displacement

  Hevilp 109 views 5 comments 0 points Most recent by Hevilp April 2018
• 
  JGaurora a5 making a loud squeaking noise!

  timosuprmo 295 views 1 comment 0 points Most recent by Samuel Pinches April 2018
• 
  Temperature issues with the A5

  GinoD 142 views 1 comment 0 points Most recent by Samuel Pinches April 2018
• 
  WARNING - Jgaurora A3S, bought from Gearbest, was a real BAD DEAL

  bargo100 396 views 9 comments 0 points Most recent by jollypike April 2018
• 
  filament is coming up

  Hevilp 261 views 6 comments 0 points Most recent by Samuel Pinches April 2018