Getting Started & Troubleshooting

Discussion List

• 
  positioning the print start

  gary74 9 views 1 comment 0 points Most recent by Samuel Pinches July 2019
• 
  Troubles with printing position

  Samuel Pinches 29 views 2 comments 0 points Most recent by Samuel Pinches July 2019
• 
  controls not working

  les88 15 views 1 comment 0 points Most recent by Samuel Pinches July 2019
• 
  leveling does not go to all four corners, stops in about 4" square, is it LCD program?

  gary74 17 views 2 comments 0 points Most recent by Samuel Pinches July 2019
• 
  Auto Bed level - noise on Y Axis movement

  Mario Wurzinger 44 views 3 comments 0 points Most recent by Der_Muck June 2019
• 
  Printing a Cube VS. Printing a Cylinder

  JayJoe 44 views 2 comments 0 points Most recent by JayJoe June 2019
• 
  Octolapse settings

  sasa 133 views 2 comments 0 points Most recent by Richy_T June 2019
• 
  A5S filament motor clicking only at beginning of print

  mgrabow 73 views 4 comments 0 points Most recent by mgrabow June 2019
• 
  Importing cura printer profiles for miniatures for A5s

  KurtMax 61 views 0 comments 0 points Most recent by KurtMax June 2019
• 
  Printer not stopping heating

  Jacob_Vaughan 65 views 4 comments 0 points Most recent by Jacob_Vaughan June 2019
• 
  Why does filament sometimes get clogged in the hot-end?

  cs2000 170 views 4 comments 0 points Most recent by ThingsNSchtuff June 2019
• 
  Printer stopped after retract

  Werewolf 54 views 19 comments 0 points Most recent by Samuel Pinches June 2019
• 
  Pause at z layer

  rhaub101 324 views 10 comments 0 points Most recent by Der_Muck May 2019
• 
  closing machine error

  aemkie 36 views 1 comment 0 points Most recent by Samuel Pinches May 2019
• 
  A5 heatbed stop heat up problem

  Robert 1.7K views 17 comments 0 points Most recent by caligarius May 2019
• 
  Bought dial gauge but all the mounts are shit, any help?

  GrayCountertop 44 views 1 comment 0 points Most recent by cs2000 May 2019
• 
  Cura Extra Prime Amount

  JetBoyTR 35 views 0 comments 0 points Most recent by JetBoyTR May 2019
• 
  Z axis steppers grinding noise TMC2130

  cs2000 351 views 16 comments 0 points Most recent by cs2000 May 2019
• 
  Printer Continuing to print after cooling down?

  Jacob_Vaughan 14 views 3 comments 0 points Most recent by Der_Muck May 2019
• 
  Replacement filament guide (bearing?)

  g_pwn 62 views 13 comments 0 points Most recent by Der_Muck May 2019
• 
  Extruder thermistor problem

  valiobg 145 views 23 comments 0 points Most recent by Der_Muck May 2019
• 
  A3 anti-interference cable

  mufasa48 41 views 2 comments 0 points Most recent by mufasa48 May 2019
• 
  SOLVED: MINTEMP triggered, system stopped! Heater_ID: 0 (Printer randomly stopping mid print)

  Peter Walsh 208 views 1 comment 0 points Most recent by Samuel Pinches May 2019
• 
  How do I replace the threaded filament tube that holds the print head?

  Sparks 121 views 16 comments 0 points Most recent by Sparks May 2019
• 
  Can't get files to read on any flash drive

  Fam4sta 113 views 10 comments 0 points Most recent by Fam4sta May 2019
• 
  Best way to clean pla off extruder

  noobmaker 166 views 8 comments 0 points Most recent by beata April 2019
• 
  Strange knocking sound from extruder carriage when printing

  valiobg 76 views 3 comments 0 points Most recent by Samuel Pinches April 2019
• 
  Mark On Top Surface

  JetBoyTR 45 views 1 comment 0 points Most recent by Laser8302 April 2019
• 
  PETG printing = a lot of frustrations

  Laser8302 221 views 9 comments 0 points Most recent by Laser8302 April 2019
• 
  Carbon fiber filament

  demillertime 400 views 19 comments 0 points Most recent by cs2000 April 2019