Getting Started & Troubleshooting

Discussion List

• 
  Print is weird and won't stick to the bed

  Winter 91 views 3 comments 0 points Most recent by Laser8302 December 2019
• 
  Clip being hit by start script when wiping

  victagayun 22 views 3 comments 0 points Most recent by Samuel Pinches December 2019
• 
  No Files Found

  Winter 138 views 11 comments 0 points Most recent by Winter December 2019
• 
  min temp reached error

  davidtriune 335 views 8 comments 0 points Most recent by Samuel Pinches November 2019
• 
  A3S V1 Air Prints from Z at Which Temperature is Set, Unless G28 (Home Extruder) is Added Manually

  poikilos 33 views 2 comments 0 points Most recent by Samuel Pinches November 2019
• 
  A3S V1 - Must Tighten Screw for Leveling Position 1 to the Maximum Amount, and Z Degreasing

  poikilos 36 views 1 comment 0 points Most recent by poikilos November 2019
• 
  LCD/Z-axis problems

  Joshua Loos 65 views 1 comment 0 points Most recent by Samuel Pinches November 2019
• 
  Stampante bloccata

  teogaspa 63 views 4 comments 0 points Most recent by Samuel Pinches October 2019
• 
  Please help!!! After each print goes to corner and extrude

  Asif 44 views 1 comment 0 points Most recent by Samuel Pinches October 2019
• 
  Starting heat settings

  rhaub101 39 views 8 comments 0 points Most recent by rhaub101 October 2019
• 
  Firmware update for A5 Mainboard and LCD controller display issues.

  John Stockdale 95 views 2 comments 0 points Most recent by Samuel Pinches October 2019
• 
  Temperature issue

  Matt 151 views 4 comments 0 points Most recent by Matt October 2019
• 
  home issue?

  Matt 27 views 0 comments 0 points Started by Matt October 2019
• 
  Temp. not correct when plugging in to PC

  g_pwn 21 views 7 comments 0 points Most recent by g_pwn October 2019
• 
  JgAurora A5 Magic number

  itisnot_me 669 views 10 comments 0 points Most recent by cmarabate October 2019
• 
  Please Diagnose my issue

  Marian Würker 63 views 2 comments 0 points Most recent by Marian Würker September 2019
• 
  Blank white screen, but printer working otherwise

  qthurtle 283 views 5 comments 0 points Most recent by qthurtle September 2019
• 
  Z axis on the JGAURORA A5S isnt moving

  Jacob Torres 62 views 4 comments 0 points Most recent by Richy_T September 2019
• 
  Filament sensor problem

  krenex 650 views 8 comments 0 points Most recent by Samuel Pinches September 2019
• 
  thermister

  les88ken 49 views 2 comments 0 points Most recent by Richy_T September 2019
• 
  Hotbed Cable Management

  Levi Döner 128 views 5 comments 0 points Most recent by rhaub101 September 2019
• 
  Hot swap filaments mid print.

  Dervick 236 views 3 comments 0 points Most recent by Richy_T August 2019
• 
  Stretched Stepper Couplers

  Dervick 49 views 1 comment 0 points Most recent by Samuel Pinches August 2019
• 
  Thermal Runaway Issue (Extruder)

  Jari Christopherson 119 views 2 comments 0 points Most recent by Jari Christopherson August 2019
• 
  A5 massive heating problems

  aemkie 82 views 5 comments 0 points Most recent by Samuel Pinches August 2019
• 
  My A5 Got Instant Smoke

  Promachine 199 views 18 comments 0 points Most recent by Promachine August 2019
• 
  Problems after change stepper drivers

  ttdriver87 54 views 4 comments 0 points Most recent by Samuel Pinches August 2019
• 
  Print Troubleshooting

  mgrabow 47 views 1 comment 0 points Most recent by Laser8302 August 2019
• 
  Micro-swiss + PETG = failed prints?

  Laser8302 1.3K views 12 comments 0 points Most recent by Laser8302 August 2019
• 
  Help To Get Better Prints?

  JetBoyTR 108 views 14 comments 0 points Most recent by Samuel Pinches August 2019