Getting Started & Troubleshooting

Discussion List

• 
  IR Sensor does not work

  Mario Wurzinger 182 views 10 comments 0 points Most recent by Samuel Pinches March 2019
• 
  Run Out Sensor (How to Actually use It)

  cs2000 133 views 4 comments 0 points Most recent by cs2000 March 2019
• 
  Print suddenly stops with no sond nor message (A3-S)

  brunolinter 83 views 9 comments 0 points Most recent by Samuel Pinches March 2019
• 
  Tuning stock stepper drivers

  rhaub101 38 views 2 comments 0 points Most recent by rhaub101 March 2019
• 
  Grinding the bed with BLTouch

  FreddyGaertner 140 views 6 comments 0 points Most recent by FreddyGaertner March 2019
• 
  TMC 2208 snipped pin issue

  itisnot_me 55 views 2 comments 0 points Most recent by itisnot_me March 2019
• 
  Z Axis Homing Issue (Too Low)

  cs2000 250 views 5 comments 0 points Most recent by Samuel Pinches February 2019
• 
  Heater Bed Cable 4 Pin Connector

  Negima 85 views 4 comments 0 points Most recent by Samuel Pinches February 2019
• 
  Problem With Stringing Inside The Shell

  JetBoyTR 44 views 5 comments 0 points Most recent by Samuel Pinches February 2019
• 
  Overheat

  Jonathan 39 views 1 comment 0 points Most recent by Samuel Pinches February 2019
• 
  Problems to level the bed.

  Wesley Manholer 63 views 2 comments 0 points Most recent by Der_Muck February 2019
• 
  Problem with jgaurora a5

  EA3GLL 70 views 1 comment 0 points Most recent by Der_Muck February 2019
• 
  A5 stops printing SOLVED

  Der_Muck 138 views 4 comments 0 points Most recent by Der_Muck February 2019
• 
  Filament feed in length

  rhaub101 84 views 3 comments 0 points Most recent by Der_Muck February 2019
• 
  Z-axis lowering after any axis homing

  netzmark 44 views 1 comment 0 points Most recent by Samuel Pinches February 2019
• 
  Z axis rattling :(

  sasa 87 views 2 comments 0 points Most recent by sasa February 2019
• 
  Y axis not working

  Jon Mathis 112 views 1 comment 0 points Most recent by Samuel Pinches February 2019
• 
  Real maximum size

  monicaco 128 views 5 comments 0 points Most recent by Touliloup February 2019
• 
  Problem with extruding and printing

  Pankh 77 views 2 comments 0 points Most recent by Samuel Pinches February 2019
• 
  Bed leveling shifting when the bed get heated

  Jamal3f 113 views 5 comments 0 points Most recent by Samuel Pinches February 2019
• 
  MINTEMP bed error at approx 180mm Y axis

  n0tch 30 views 0 comments 0 points Most recent by n0tch February 2019
• 
  Heatbed

  tam 50 views 0 comments 0 points Most recent by tam February 2019
• 
  Extruder malfunction,

  Vangelis Andy Roussos 82 views 4 comments 0 points Most recent by Samuel Pinches February 2019
• 
  Moving in wrong direction after bed leveling

  ricard0g0mes 32 views 1 comment 0 points Most recent by Der_Muck February 2019
• 
  Strange Y-Axis behaviour after TMC2130 upgrade

  blindidiotscout 58 views 0 comments 0 points Most recent by blindidiotscout February 2019
• 
  Break after 9hrs and 20 minutes

  M16rulez 73 views 2 comments 0 points Most recent by Samuel Pinches February 2019
• 
  Layer Shifts with certain models

  Jacob_Vaughan 134 views 2 comments 0 points Most recent by Jacob_Vaughan February 2019
• 
  JG Aurora A5 Print head crashed into bed and now nothing works

  outlawal2 139 views 11 comments 0 points Most recent by Richy_T February 2019
• 
  Filament broken in tube, how do i get it out?

  wlaubach 159 views 4 comments 0 points Most recent by Samuel Pinches January 2019
• 
  Prints stopping mid-print when printing from LCD via USB stick

  System 343 views 7 comments 0 points Most recent by Samuel Pinches January 2019