NEW Budget 3D Printer: JGMaker Magic - here's the best deals at the moment:
- Gearbest: Flash sale for $189
- Banggood Store: Take off $20 with coupon bd5cc5
- Amazon USA - $30 instant discount coupon

[6th Nov 18] The NEW recently released JGAurora A5S is already for sale under $400! Print quality is better than A5 out of the box.
Click here to check out this deal!

Getting Started & Troubleshooting

Clogging at the beginning of the heat break

Hevilp 42 views 2 comments 0 points Most recent by Hevilp July 2018
Short circiut on heat element - board broken?

Hevilp 46 views 6 comments 0 points Most recent by Samuel Pinches July 2018
Broken steppers?

Jari Christopherson 178 views 12 comments 0 points Most recent by Jari Christopherson July 2018
Automatically paused during a build?

Harry Xiao 187 views 20 comments 0 points Most recent by AETEK July 2018
Noise from hot end fan on start up

smaprint 282 views 6 comments 0 points Most recent by AETEK July 2018
Errors in the documentation for the MKS GEN_L 1.0 motherboard (EXP1 & EXP2)

AETEK 208 views 2 comments 0 points Most recent by AETEK July 2018
Can't move after manually stopped the build process?

Harry Xiao 58 views 8 comments 0 points Most recent by Samuel Pinches July 2018
the hot bed does not heat

navalgijon 63 views 1 comment 0 points Most recent by Samuel Pinches July 2018
A5 LCD flashing "Booting..." and beeping at the same time.

CVivian 64 views 1 comment 0 points Most recent by Samuel Pinches July 2018
Help with print settings

sanjibukai 479 views 1 comment 0 points Most recent by Samuel Pinches July 2018
Bed Leveling Screws/Springs - Very Tight... stripping knobs

Nitro66215 137 views 2 comments 0 points Most recent by Nitro66215 July 2018
not extruding anything

davidtriune 372 views 11 comments 0 points Most recent by seafian July 2018
Temp froze on screen

Patricia Larkin 39 views 1 comment 0 points Most recent by Samuel Pinches July 2018
Reverse axis and general troubleshooting TMC2130 v1.1

Ophiocos 261 views 2 comments 0 points Most recent by Ophiocos July 2018
A5 Nozzle temperature reads -15 degrees

dandan 166 views 23 comments 0 points Most recent by dandan July 2018
Nozzle way off the bed after nozzle change

fuzio 65 views 4 comments 0 points Most recent by Samuel Pinches July 2018
Heated bed not working

hexoplexo 91 views 13 comments 0 points Most recent by AETEK July 2018
a few questions

nach00 37 views 0 comments 0 points Most recent by nach00 July 2018
Bed leveling mesh not applying

sanjibukai 126 views 10 comments 0 points Most recent by Samuel Pinches July 2018
Absolute tangled mess misprints... what’s up!?

jschub 62 views 1 comment 0 points Most recent by Samuel Pinches July 2018
Getting rid of z-seam and underextrusion

System 368 views 11 comments 0 points Most recent by Samuel Pinches July 2018
Brand new A5 - front-panel DOA?

omninate 60 views 3 comments 0 points Most recent by Samuel Pinches July 2018
Z-axis not moving at all

nach00 379 views 20 comments 0 points Most recent by seafian July 2018
What are the two thin wires connected near the nozzle?

nach00 70 views 16 comments 0 points Most recent by Samuel Pinches July 2018
can't save bed leveling data

davidtriune 137 views 2 comments 0 points Most recent by davidtriune July 2018
Error in the documentation for the MKS TFT2.8

AETEK 58 views 1 comment 0 points Most recent by Samuel Pinches July 2018
Touch panel "debouncing"

seafian 110 views 2 comments 0 points Most recent by seafian July 2018
PETG prints stops after a while

Hevilp 312 views 8 comments 0 points Most recent by Samuel Pinches July 2018
The pinout designations of the MKS-GEN_L 1.0 documentation are partly faulty

AETEK 1K views 2 comments 0 points Most recent by AETEK July 2018
Y axis issues / bed nut impacting on base

jollypike 72 views 1 comment 0 points Most recent by jollypike July 2018