JGMaker is having a CLEARANCE sale on the commercial-grade Z-603S -- at a BONKERS $399. If you're in the USA, and want a ready-to-go full steel frame printer... run, don't walk! ⏩ JGAURORA Z603S CLEARANCE ⏪ Only 4 units left!

JGAurora A5S on Sale at Amazon USA - $339, with $60 off!
JGMaker Magic on Sale for $208, with $20 instant discount coupon!.

Modifications & Upgrades

How to compile Marlin 2.0 firmware for JGAurora A5 - Community Firmware (2.0H) - 2021 Guide

Announcement Samuel Pinches 188 views 3 comments 0 points Most recent by Samuel Pinches April 9
E3D V6 hotend conversion for A5

Announcement Jozko Remen 274 views 4 comments 0 points Most recent by Jozko Remen December 2020
Check out the wiki for many upgrades for your A5 or A3S printer...

Announcement Samuel Pinches 2.5K views 4 comments 0 points Most recent by Samuel Pinches October 2020
Upgrade to TMC2208 Stepper Drivers

Announcement Samuel Pinches 6.7K views 44 comments 0 points Most recent by Roger April 2020
MKS PWC V2.0 auto off after printing end with A5

Announcement coolt5 560 views 0 comments 0 points Started by coolt5 March 2020
[Project] Upgrading the A5 to Direct Drive + full metal hotend + auto bed leveling for under 60$

Announcement Prokktor 5.4K views 27 comments 0 points Most recent by Samuel Pinches January 2020
A5 - and what became out of it...

Announcement Charly3 493 views 3 comments 0 points Most recent by Charly3 September 2019
Important things to know regarding stepper upgrade with TMC 2130 with SPI

Announcement Enrique Riri 2K views 26 comments 0 points Most recent by Samuel Pinches April 2019
Makerbase mkstft28 replacement questions?

mrfalk 14 views 2 comments 0 points Most recent by mrfalk May 6
JG aurora a 5 flexible cam holder thingy

Eye 13 views 2 comments 0 points Most recent by Eye May 3
Which Cooling Duct to choose?

System 1.4K views 18 comments 0 points Most recent by Eye April 21
JGAurora A5 - Linear rail X - MGN12 - H

jsanch 300 views 7 comments 0 points Most recent by Derf April 21
Building a Box / Scrap upecyling ;)

Eye 16 views 0 comments 0 points Started by Eye April 19
cutting cables

Matt 78 views 16 comments 0 points Most recent by Eye April 19
Problem with i Box

jirgel 435 views 15 comments 0 points Most recent by ChAoS March 24
Bowden tube fittings?

GrayCountertop 174 views 5 comments 0 points Most recent by Eye March 7
A5 Heating Problem

niRvanati 17 views 2 comments 0 points Most recent by Samuel Pinches March 7
Tinkering Thread: Marlin Firmware for the A5 main board (1.1.8C --> 2.x) with LCD firmware (v.3.03)

Eye 50 views 8 comments 0 points Most recent by Eye February 20
Installing a Duet in the A5

kellis19 118 views 2 comments 0 points Most recent by Sergey February 13
JGAurora A5 Thermistor

mmmmarto 43 views 2 comments 0 points Most recent by michalko99 February 4
Hotbed 310x310 24v question?? Help!!

Erwaly 38 views 4 comments 0 points Most recent by Erwaly January 28
JGAurora A5 drivers without potentiometers

netzmark 295 views 14 comments 0 points Most recent by Matt January 18
Still troubles with z-axis

Matt 68 views 12 comments 0 points Most recent by Matt January 17
Looking to upgrade some stuff

noobmaker 44 views 3 comments 0 points Most recent by michalko99 January 15
Where to route a bed probe sensor cable on the A5?

noobmaker 23 views 2 comments 0 points Most recent by noobmaker January 14
Replacement linear bearings

ToTo 203 views 7 comments 0 points Most recent by michalko99 January 11
Marlin 2.0 and 32bit board for JGAURORA A5. It is workable?

Werewolf 1.4K views 22 comments 0 points Most recent by Gandy January 3
How to upgrade A5 to dual extruder

Thomas 4.8K views 23 comments 0 points Most recent by Felix December 2020
MKS Gen_L V2.0

Joshua Loos 2.2K views 10 comments 0 points Most recent by doug_scott December 2020
JGAURORA A5S to MKS GEN L v1.0 / TMC2209 with MKS TFT35 Help Please

Soko 65 views 0 comments 0 points Started by Soko November 2020
Non-planar slicing?

Matt 49 views 2 comments 0 points Most recent by Matt November 2020
BMG Dual drive extruder & mount more topwards

Jozko Remen 339 views 23 comments 0 points Most recent by kartal2_ocal November 2020
A5 heatbed mod to get higher temps – possible?

Jozko Remen 42 views 9 comments 0 points Most recent by Jozko Remen November 2020
Dial Indicator offset when mesh leveling ?

FreddyGaertner 34 views 1 comment 0 points Most recent by Samuel Pinches October 2020
A5 – BLtouch goes off the bed during UBL bed leveling

Jozko Remen 25 views 2 comments 0 points Most recent by Samuel Pinches October 2020