Modifications & Upgrades

Discussion List

• 
  Upgrade bearings for x and y axis

  ufodoctor3 1.1K views 68 comments 0 points Most recent by ufodoctor3 July 2019
• 
  A3S Internal Power Supply.

  Patrick McCreanor 22 views 1 comment 0 points Most recent by Samuel Pinches July 2019
• 
  thyrister was bad and ordered a new A5 hotbed, but the new bed has 6 pins instead of 4 whats next?

  gary74 47 views 3 comments 0 points Most recent by gary74 June 2019
• 
  What part fan duct do you use?

  Laser8302 196 views 3 comments 0 points Most recent by ThingsNSchtuff June 2019
• 
  Bowden Extruder

  tay916 337 views 6 comments 0 points Most recent by tay916 June 2019
• 
  Closing Machine Error

  aemkie 25 views 1 comment 0 points Most recent by Der_Muck May 2019
• 
  A5 + BLTOUCH +CURA 4 Start GCODE

  chrisonmoon 498 views 2 comments 0 points Most recent by Laser8302 May 2019
• 
  BLTouch and UBL - bed skew and bad adhesion?

  beata 278 views 6 comments 0 points Most recent by Laser8302 May 2019
• 
  Change Language on MKS TFT

  Samuel Pinches 258 views 0 comments 0 points Most recent by Samuel Pinches May 2019
• 
  The Spaghetti Detective

  cs2000 149 views 3 comments 0 points Most recent by Samuel Pinches May 2019
• 
  Make Thermal Runaway Detection Less Sensitive?

  cs2000 123 views 4 comments 0 points Most recent by cs2000 May 2019
• 
  Useful info for anyone wanting further customisation on the LCD

  cs2000 66 views 2 comments 0 points Most recent by GrayCountertop May 2019
• 
  Nozzle sizes

  Enrique Riri 1K views 19 comments 0 points Most recent by tay916 May 2019
• 
  Overkill modification, is it even possible?

  GrayCountertop 112 views 6 comments 0 points Most recent by Samuel Pinches May 2019
• 
  IR Sensor Sometimes Triggers Too Early

  ryanh1904 48 views 2 comments 0 points Most recent by cs2000 May 2019
• 
  Upgrades to my A5 - BLtouch, controller fan and cold end fan control

  Laser8302 310 views 3 comments 0 points Most recent by Laser8302 May 2019
• 
  How the filament out sensor works

  AETEK 1.5K views 11 comments 0 points Most recent by LouieRobotech May 2019
• 
  What are the stepper motors in the A5?! (Working out correct TMC21xx voltages)

  cs2000 538 views 3 comments 0 points Most recent by cs2000 May 2019
• 
  JGAurora A5 Firmware 1.1.8

  itisnot_me 321 views 7 comments 0 points Most recent by hombre666 May 2019
• 
  Problem with Nozzle replacement

  ufodoctor3 123 views 6 comments 0 points Most recent by ufodoctor3 April 2019
• 
  Finally I've gone direct drive, but...

  Matt 239 views 19 comments 0 points Most recent by Matt April 2019
• 
  Bowden tube fittings?

  GrayCountertop 103 views 3 comments 0 points Most recent by Samuel Pinches April 2019
• 
  Any helpful things I should print to upgrade the printer?

  GrayCountertop 52 views 0 comments 0 points Most recent by GrayCountertop April 2019
• 
  All metal throat

  demillertime 1.1K views 11 comments 0 points Most recent by Der_Muck April 2019
• 
  Installing a Duet in the A5

  kellis19 90 views 1 comment 0 points Most recent by Samuel Pinches April 2019
• 
  Hotbed goes in the wrong direction after tmc 2208 update

  Michel78 117 views 9 comments 0 points Most recent by Michel78 April 2019
• 
  IR Sensor Upgrade Wiki Changes (Comments and Suggestions)

  cs2000 162 views 12 comments 0 points Most recent by Samuel Pinches April 2019
• 
  Question about TL smoothers?

  chilman408 209 views 5 comments 0 points Most recent by Laser8302 April 2019
• 
  Power fan

  itisnot_me 128 views 13 comments 0 points Most recent by Samuel Pinches April 2019
• 
  Important things to know regarding stepper upgrade with TMC 2130 with SPI

  Announcement Enrique Riri 1.8K views 26 comments 0 points Most recent by Samuel Pinches April 2019