Modifications & Upgrades

Discussion List

• 
  Ptfe tube? Which diameter

  Hevilp 360 views 6 comments 0 points Most recent by Der_Muck January 2019
• 
  A5 doesn't start printing, seems to freeze on start

  Badger1875 629 views 14 comments 0 points Most recent by Badger1875 January 2019
• 
  A5 Magnetic Bed Mod

  Zrvl 891 views 10 comments 0 points Most recent by Darius R. Steele January 2019
• 
  Replacing 4 pins with 6 pins heater bed

  Cedric 77 views 2 comments 0 points Most recent by Osama December 2018
• 
  TCM2XXX why should I need Firmware 1.1.9C?

  Prokktor 351 views 10 comments 0 points Most recent by netzmark December 2018
• 
  Benefit of TMC2208 vs TMC2130

  g_pwn 14.6K views 4 comments 0 points Most recent by netzmark December 2018
• 
  1.1.9 -C version

  Hindawi 248 views 11 comments 0 points Most recent by Samuel Pinches December 2018
• 
  Print carriage/head

  itisnot_me 146 views 3 comments 0 points Most recent by Prokktor December 2018
• 
  Using 12V stuff in my A5, need help!

  Prokktor 145 views 8 comments 0 points Most recent by Andre December 2018
• 
  TFT28 V4 vs V3 firmware issues

  Enrique Riri 781 views 12 comments 0 points Most recent by Marco Salvetti December 2018
• 
  Auto leveling with 3dtouch

  Johan Lutters 229 views 3 comments 0 points Most recent by Samuel Pinches December 2018
• 
  Can't flash LCD with custom firmware?

  Jari Christopherson 87 views 2 comments 0 points Most recent by Jari Christopherson December 2018
• 
  mesh bed leveling gcode problem A5

  bernd1000 111 views 1 comment 0 points Most recent by Prokktor December 2018
• 
  Z not working properly after 1.1.8c a3s update

  Swarfing 77 views 16 comments 0 points Most recent by Samuel Pinches November 2018
• 
  Auto Leveling problem with z axis

  hexoplexo 161 views 7 comments 0 points Most recent by Samuel Pinches November 2018
• 
  Motherboard upgrade

  demillertime 740 views 7 comments 0 points Most recent by Andre November 2018
• 
  5 Volt fan for coldend cooling

  stevema 130 views 8 comments 0 points Most recent by Samuel Pinches November 2018
• 
  change broken trapezoidal screws

  djaurora 191 views 5 comments 0 points Most recent by Andre November 2018
• 
  PROBLEMAS CON LA IMPRESION. | Problem with print shifted to the corner

  jonaneriz 247 views 1 comment 0 points Most recent by Samuel Pinches November 2018
• 
  X carriage IGUS conversion

  RoLL 351 views 6 comments 0 points Most recent by Samuel Pinches November 2018
• 
  led lamp addon

  Matt 315 views 22 comments 0 points Most recent by Matt November 2018
• 
  Dual Extruder / e3d chimera 2 in 2 out

  kse 160 views 2 comments 0 points Most recent by kse November 2018
• 
  Advanced Nozzle Priming

  AETEK 440 views 12 comments 0 points Most recent by netzmark November 2018
• 
  Cura printing time estimate not accurate after steppers upgrade?

  sasa 69 views 0 comments 0 points Most recent by sasa November 2018
• 
  A5 Direct Drive Modification

  System 1.1K views 5 comments 0 points Most recent by Matt November 2018
• 
  Z Gantry Stiffener

  RoLL 160 views 1 comment 0 points Most recent by Samuel Pinches November 2018
• 
  Soft bed

  netzmark 48 views 4 comments 0 points Most recent by netzmark November 2018
• 
  IR Probe, PWM Fan Mod, and TMC2208 Drivers firmware setup

  TechnoGangsta 188 views 19 comments 0 points Most recent by netzmark November 2018
• 
  Auto Bed Leveling inaccurate

  Tim92 293 views 2 comments 0 points Most recent by Tim92 October 2018
• 
  Can't compile with AUTO BED LEVELING BILINEAR

  Tim92 1.7K views 2 comments 0 points Most recent by Tim92 October 2018