Getting Started & Troubleshooting

Discussion List

• 
  NEW A5S Official Firmware - April 25th 2019

  Announcement Samuel Pinches 866 views 6 comments 0 points Most recent by Spark August 2019
• 
  LCD crashing

  Stuart George Damon 36 views 4 comments 0 points Most recent by baconCheeseFry August 13
• 
  Replacement y axis stepper motor issue

  NicolaGibson 21 views 3 comments 0 points Most recent by Dervick August 8
• 
  Bed Thermal Runaway and Display barely working

  GNWarrior 33 views 9 comments 0 points Most recent by giantrobot2001 August 5
• 
  A5S stopping mid print

  suhling85 22 views 3 comments 0 points Most recent by suhling85 August 5
• 
  So... Thermistor question.

  Richy_T 27 views 2 comments 0 points Most recent by Richy_T July 13
• 
  Killed it. Help :(

  Richy_T 64 views 18 comments 0 points Most recent by Richy_T July 13
• 
  If I use Bedleveling the slicer tell me the need up to 4 times of time

  topoli 12 views 3 comments 0 points Most recent by giantrobot2001 July 10
• 
  A5S OEM Firmware

  poopym 49 views 3 comments 0 points Most recent by Samuel Pinches July 9
• 
  Warped bed and used printer?

  uwbe25 39 views 4 comments 0 points Most recent by Samuel Pinches July 9
• 
  Buying Advice - A5S vs. A1 vs. Anycubic Mega X

  spooknik 74 views 17 comments 0 points Most recent by giantrobot2001 July 1
• 
  Initial Layer always too thin- Calibrating Z axis - solved

  topoli 30 views 0 comments 0 points Started by topoli June 21
• 
  Calibration Extruder problems

  topoli 18 views 0 comments 0 points Started by topoli June 21
• 
  Nozzle clear but still not extruding?

  Phyllis Bulkin Lehrer 23 views 2 comments 0 points Most recent by Samuel Pinches June 18
• 
  Repeatable Z-banding

  spooknik 19 views 0 comments 0 points Started by spooknik June 17
• 
  A5S major Z axis failure

  Razai 64 views 7 comments 0 points Most recent by Razai June 16
• 
  Solved Print Problems with CURA 4.5 and 4.6

  topoli 35 views 0 comments 0 points Started by topoli June 15
• 
  Thread to the extruder

  tfedder 20 views 5 comments 0 points Most recent by tfedder June 12
• 
  Flashing the Firmware with ST-Link (unable to communicate through USB)

  giantrobot2001 42 views 15 comments 0 points Most recent by Samuel Pinches June 11
• 
  A1 heat break PTFE diameter?

  vintageb3 14 views 0 comments 0 points Started by vintageb3 May 24
• 
  A1 manual

  vintageb3 23 views 2 comments 0 points Most recent by vintageb3 May 24
• 
  PrusaSlicer profile for A1?

  vintageb3 21 views 2 comments 0 points Most recent by vintageb3 May 19
• 
  Filament grinding

  JetBoyTR 79 views 14 comments 0 points Most recent by Samuel Pinches May 14
• 
  A5S Hot end sock .

  MarkMarcum 83 views 10 comments 0 points Most recent by giantrobot2001 May 12
• 
  JGAurora A5S - No Files to print on the LCD when I put the SD card in.

  giantrobot2001 185 views 74 comments 0 points Most recent by giantrobot2001 May 10
• 
  Comparison of JGAurora A5S and A1

  Samuel Pinches 928 views 17 comments 0 points Most recent by Samuel Pinches May 9
• 
  Printer doesn´t start for specific model

  bukl 19 views 5 comments 0 points Most recent by Samuel Pinches May 3
• 
  JGAurora A5S Makes beeping sound and screen doesn't work

  luz0928 124 views 12 comments 0 points Most recent by Stephen Todd May 3
• 
  a5s beeping loud screen flashing

  mikemullaney1320 16 views 0 comments 0 points Started by mikemullaney1320 May 2
• 
  Bed Leveling not active at start-up

  bukl 42 views 4 comments 0 points Most recent by Samuel Pinches April 26
• 
  Issues with A5S

  Lickaholic 96 views 9 comments 0 points Most recent by Lickaholic April 25