Getting Started & Troubleshooting

Discussion List

• 
  Carbon Fiber Filament Jamming

  mgrabow 64 views 3 comments 0 points Most recent by mgrabow August 2019
• 
  Gcode to have mesh bed leveling! - make sure you have it there!

  Spark 77 views 0 comments 0 points Started by Spark August 2019
• 
  NEW A5S Official Firmware - April 25th 2019

  Announcement Samuel Pinches 866 views 6 comments 0 points Most recent by Spark August 2019
• 
  Fat Error when loading in new and flash firmware.

  Voltis 71 views 2 comments 0 points Most recent by Samuel Pinches August 2019
• 
  A5S won't keep 220 nozzle temp

  Learning_Curve 43 views 2 comments 0 points Most recent by Samuel Pinches August 2019
• 
  A5S Won't heat bed

  rmize01 83 views 3 comments 0 points Most recent by Samuel Pinches August 2019
• 
  Anyone able to print with a pi/octoprint setup?

  cpwines18 133 views 6 comments 0 points Most recent by Samuel Pinches August 2019
• 
  A5S says it's printing but doesn't

  Ovark 647 views 19 comments 0 points Most recent by Samuel Pinches August 2019
• 
  a5s under extrusion

  iam2sick4you2 71 views 1 comment 0 points Most recent by Samuel Pinches August 2019
• 
  you thoughts on the best slicer program to run the a5s on ?

  sonicdrive 96 views 2 comments 0 points Most recent by chainbreaker2012 August 2019
• 
  first layer to thin after leveling

  chainbreaker2012 109 views 12 comments 0 points Most recent by chainbreaker2012 July 2019
• 
  What causes gaps in print

  WidgetElgie 34 views 4 comments 0 points Most recent by Samuel Pinches July 2019
• 
  How to setup the cooling fan to shut off when the print has completed?

  WidgetElgie 78 views 3 comments 0 points Most recent by WidgetElgie July 2019
• 
  A5S touch screen blank

  Robert Nunes 116 views 3 comments 0 points Most recent by John Buswell July 2019
• 
  Beginner Questions - How to Optimize Print Speeds

  WidgetElgie 252 views 4 comments 0 points Most recent by WidgetElgie July 2019
• 
  Slicer Supports Settings

  SomeoneYouLike 77 views 0 comments 0 points Most recent by SomeoneYouLike July 2019
• 
  Unable to launch printing from se card

  Scruffy 61 views 2 comments 0 points Most recent by Samuel Pinches July 2019
• 
  So this happened

  rhythmdave 64 views 2 comments 0 points Most recent by rhythmdave July 2019
• 
  printer unloading filament mid print

  Amyliz93 40 views 1 comment 0 points Most recent by Samuel Pinches July 2019
• 
  Here's a doozy for ya...A1, A5S, etc.

  rhythmdave 74 views 1 comment 0 points Most recent by Samuel Pinches July 2019
• 
  A1 custom community firmware and Octoprint

  rhythmdave 47 views 1 comment 0 points Most recent by Samuel Pinches July 2019
• 
  A5S Solutions and problems from a new A5S owner

  Bigtriver 201 views 4 comments 0 points Most recent by Samuel Pinches July 2019
• 
  Edges of curves have flat spots

  mgrabow 26 views 5 comments 0 points Most recent by mgrabow July 2019
• 
  JGaurora A5S firmware problems

  D_Hansen81 941 views 5 comments 0 points Most recent by Samuel Pinches July 2019
• 
  Please help

  ruins 64 views 8 comments 0 points Most recent by Samuel Pinches July 2019
• 
  Odd issue - Bed Temp, Nozzle Temp and extruder all stop during the print

  Simulanon 35 views 4 comments 0 points Most recent by Simulanon July 2019
• 
  A1 only fan working

  Andi Robinson 34 views 1 comment 0 points Most recent by Samuel Pinches July 2019
• 
  New JGaurora A5 V4.0 board has new firmware with wifi?

  Scottmg 109 views 5 comments 0 points Most recent by Scottmg July 2019
• 
  PLA Ultimaker Cura settings

  Amyliz93 195 views 2 comments 0 points Most recent by Laser8302 July 2019
• 
  A1 - Have to level it often

  Spark 20 views 3 comments 0 points Most recent by Samuel Pinches July 2019