› ›
JGAurora A5S on Sale at Amazon USA - $339, with $60 off!
JGMaker Magic on Sale for $208, with $20 instant discount coupon!.

Updated Marlin Firmware not working

mackpeedmackpeed Posts: 9Member
in Getting Started & Troubleshooting
New to the 3d Printing world, and now having problem with my firmware update.  Had several problems with the firmware that came installed on printer so I decided to upgrade.  Now the printer does not respond to any commands.  Any help appreciated.

Comments

  • Laser8302Laser8302 Posts: 170Member, 🌟 Super Member 🌟
    Can you connect with protorface? Send a M502, M500, M503 command and send us what the output is.

    I'm assuming you selected the correct board in the Arduino IDE before the flash correct?
  • Samuel PinchesSamuel Pinches Posts: 2,791Administrator
    edited May 2020
    @mackpeed welcome - did you unplug the LCD before flashing?
    Post edited by Samuel Pinches on
  • mackpeedmackpeed Posts: 9Member
    Yes LCD was unplugged.  Will download protoface and try.  Thanks
  • mackpeedmackpeed Posts: 9Member
    This is what I got off ponterface.
    Connecting...
    start
    Printer is now online.
    echo:Marlin 2.0.5.3
    echo: Last Updated: 2020-03-31 | Author: (none, default config)
    echo:Compiled: May 13 2020
    echo: Free Memory: 5786  PlannerBufferBytes: 1136
    echo:Hardcoded Default Settings Loaded
    echo:  G21    ; Units in mm (mm)
    echo:; Filament settings: Disabled
    echo:  M200 D3.00
    echo:  M200 D0
    echo:; Steps per unit:
    echo: M92 X80.00 Y80.00 Z4000.00 E500.00
    echo:; Maximum feedrates (units/s):
    echo:  M203 X300.00 Y300.00 Z5.00 E25.00
    echo:; Maximum Acceleration (units/s2):
    echo:  M201 X3000.00 Y3000.00 Z100.00 E10000.00
    echo:; Acceleration (units/s2): P<print_accel> R<retract_accel> T<travel_accel>
    echo:  M204 P3000.00 R3000.00 T3000.00
    echo:; Advanced: B<min_segment_time_us> S<min_feedrate> T<min_travel_feedrate> J<junc_dev>
    echo:  M205 B20000.00 S0.00 T0.00 J0.01
    echo:; Home offset:
    echo:  M206 X0.00 Y0.00 Z0.00
    echo:; PID settings:
    echo:  M301 P22.20 I1.08 D114.00
    Error:Thermal Runaway, system stopped! Heater_ID: 0
    [ERROR] Error:Thermal Runaway, system stopped! Heater_ID: 0

    Error:Printer halted. kill() called!
    [ERROR] Error:Printer halted. kill() called!

  • Samuel PinchesSamuel Pinches Posts: 2,791Administrator
    Ok, so there is something wrong with the temperature measurements. Are the nozzle or bed hot when you turn the printer on? Or perhaps is a thermistor cable loose for the bed or the nozzle?

    https://jgaurorawiki.com/a5/faq#problemheating-problems-with-nozzle-or-heated-bed

  • mackpeedmackpeed Posts: 9Member
    It does appear that the therminster is the problem.  Thanks for the help.
Sign In or Register to comment.